Risk Management - Articles - Page 31

International Glove Association 2019 Glove Symposium

March 17-19, Green Valley Ranch, Henderson, NV

February 1, 2019

Plan to join the International Glove Association (IGA) in Henderson, NV, near Las Vegas, this March to learn more about developments in workplace hand protection.

toxic exposures, OSHA permissible exposure limits

Exposure effects explained

New terms & calculations require worker retraining

Dan Markiewicz MS, CIH, CSP, RMP

February 1, 2019

A basic understanding of the toxicological dose-response curve is a necessity for OHS pros. People fear most what they understand the least. New and vast toxicological information can trigger fear and irrational actions.

Combustible dust FAQs

Know the hierarchy of risk controls to effectively mitigate hazards

Scott Francis

February 1, 2019

Combustible dust is present in a variety of industries and is the precursor to a serious hazard. This hazard's often-destructive nature makes it vitally important to understand. When accounting for the hazard, several questions arise, highlighting the true complexities of combustible dust.

Compressed air can be lethal

Workplace injuries, often created by misuse, can be devastating

Jim Krebs

January 17, 2019

OSHA standard 1910.242(b) relating to hand and portable powered tools and other hand-held equipment is clear on using compressed air for cleaning. “Compressed air shall not be used for cleaning purposes except where reduced to less than 30 psi and then only with effective chip guarding and personal protective equipment.”

5 ways to overcome challenges of foot protection programs

Why risk foot injuries?

Lori Hyllengren

January 9, 2019

Outfitting employees with appropriate footwear reduces injuries. Making sure workers have the right footwear for the job is a real, ongoing challenge for safety managers. Here are five ways you can overcome it and take advantage of all the benefits of high-quality safety footwear.

2019 top standards- OSHA Most Frequently Violated Standards

OSHA respiratory protection standard

Respiratory Protection (1910.134)- OSHA’s respiratory protection standard was the fourth most-frequently cited agency standard in FY 2018.

January 7, 2019

OSHA's Respiratory Protection Standard applies to general industry, construction, shipyards, marine terminals, and longshoring. The OSHA respirator standard applies to all occupational airborne exposures to contaminated air where the employee is.

2019 top standards- OSHA Most Frequently Violated Standards

OSHA hazard communication standard

Hazard Communication (1910.1200) OSHA’s hazard communication standard was the second most-frequently cited agency standard in FY 2018.

January 7, 2019

This occupational safety and health standard is intended to address comprehensively the issue of classifying the potential hazards of chemicals, and communicating information concerning hazards and appropriate protective measures to employees, and to preempt any legislative or regulatory enactments of a state, or political subdivision of a state, pertaining to this subject.

Respirator fit testing: real-time measurements for safety & efficiency

Finding the right mask match

Greg Olson

January 3, 2019

In the United States, workers required to wear respiratory protection must pass an annual respirator fit test. Fit tests help companies ensure worker safety by verifying a respirator can provide an OSHA-mandated and standardized level of protection.

How to maintain & repair walking-working surfaces

Plan each step

Karen Hamel

January 3, 2019

Few employees may ever take notice of a freshly cleaned, well-maintained floor. Unfortunately, too few also tend to notice uneven surfaces that cause trips or spilled materials that can make floors slippery. That’s one of the reasons why it’s up to employers to make sure that these types of hazards are eliminated.

When you can’t see, smell or hear hazards

Here’s how to improve your arc flash & electrical safety training

Jim Schuster

December 21, 2018

Working on electrical equipment exposes a worker to electric shock and arc flash hazards. Unlike many safety concerns, these hazards simply can’t be eliminated or avoided as working on or around energized equipment is often required for some tasks, such as using a meter to test for voltage or rack a breaker.